<<

T1 baseline calibration
TA Instrument Explorer
    settings
TA Instruments offices
TA Instruments patents
TA Instruments trademarks
TA on the Web
TA support
TAMA
   Event Logging for TAMA
   Using the TA Instrument Explorer
    event logging
TAMA account
temperature calibration
   Calibrating the DSC Cell Constant & Temperature
   DSC Calibration Wizard
   DSC Calibration Wizard Constant & Temperature
    run
temperature calibration parameters
temperature data compression threshold
temperature limits
   Method Segment Has Invalid Temperature Limits
   Setting Calibration Limits
temperature table
Temperature too hot for pan. Change either the pan type or the temperature.
templates
    DSC Zero Baseline
test
    sequence summary
    Zero Baseline
testing instrument components automatically
tests
    scheduling
tests/creating your own
The analysis limits must be between __ and __ °C.
The backup operation has been completed.
The baseline calibration cannot be sent
The calibration file is for cell S/N < > not the current cell.
The cell has been removed.
The cell has been replaced.
The curve contains analysis results which will be deleted when this change is made.
The curve contains analysis results. Do you want to continue to change the x-axis?
The data is not continuous between the selected limits.
The destination computer can not connect to the instrument.
The exotherm values of the two files are different.
The file you are sending to the instrument is a critical file. If the transfer fails, the instrument may not run. Please use the Instrument Setup Wizard to transfer the file. Are you sure you want to continue?
The heat flow signal used to generate this calibration file does not match the current heat flow selection.
The instrument did not accept the calibration data. Retry the calibration.
The instrument does not have enough free flash disk space to download a new executable file.
The instrument is currently running. Are you sure you want to close the lids?
The instrument is currently running. Are you sure you want to open the lids?
The instrument is not ready to start the experiment.
The instrument type is not supported or the required component is missing
The ramp was not long enough for a successfull Tzero calibration.
The restore operation has been completed.
The sample interval must be divisible by 0.5.
The Sapphire Delta T signal is not lower than the Baseline Delta T signal value.
   Sapphire Delta T Signal is Not Correct
   SDT Heat Flow Calibration - Sapphire Delta T Incorrect
The selected language does not exist in the instrument. You must update module software.
The T1 Heat Flow signal cannot be used to conduct modulated experiments.
This operation is illegal for a non-master controller.
This operation is prohibited by 21 CFR restriction.
This program requires you log in as a master controller.
tiling windows
time
    synchronizing PC and instrument
time limits
tool bar
touch screen
   Introducing the Touch Screen
   Touch Screen Calibration Successful
   Window Already Open on Touch Screen
    Autosampler calibration options
    Autosampler Control
    Autosampler manual calibration
    Autosampler sensor status
    Autosampler test options
    calibrating
       Calibrating the QNX Touch Screen
       Selecting the Instrument Preferences
    Control Menu
    customizing
    description
    introduction
    primary function keys
touch screen language
trademarks
Transferred file failed.
transferring audit trail messages
transferring data
transformer
    installing
transitition direction
transporting the Autosampler
transporting the instrument
troubleshooting data file access
Two unique file names must be specified.
Tzero calibration
   Calibrating Tzero
   DSC Calibration Wizard
   DSC Calibration Wizard Constant & Temperature
   DSC Calibration Wizard Resistance & Capacitance Step 1
   DSC Calibration Wizard Resistance & Capacitance Step 2
Tzero Calibration Error
Tzero Press
Tzero slope or offset data is equal to zero.

Unable to transfer Tzero calibration information to the instrument.
Unsupported calibration type.

Verify transferred program file failed.
Verify transferred string file failed.
voltage configuration unit
    installing

Warning: Baseline sample size is non-zero. The calibration may not be accurate.
Weight calibration coefficients out of range
Weight calibration coefficients out of range.
Windows Messaging
Windows sockets initialization failed.
wizard
   DSC Calibration Wizard
   Entering Sample Information Using the Wizard
   Starting the DSC Wizard
   Using the Instrument Setup Wizard
    calibration
    calibration experiment results
    constant and temperature calibration
    constant and temperature calibration run
    entering sample information
    experimental
    resistance & capacitance calibration step 1
    resistance & capacitance calibration step 2
Wrong cell number.

You are not allowed to make any change on the current run.
You can not change runs while the DSC calibration is in progress.
You cannot continue to the next page until a project has been selected.
You have just activated the Service menu.
You have made some change on your setup pages.
You must either confirm the change or click Cancel before you can switch to the next page.

Zero Baseline test
Zero heat flow segment